Search results

Gives a bibliographical review of the finite element methods (FEMs) applied for the linear and nonlinear, static and dynamic analyses of basic structural elements from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore aims to give the reader an encyclopaedic view on the subject. The bibliography at the end of the paper contains 2,025 references to papers, conference proceedings and theses/dissertations dealing with the analysis of beams, columns, rods, bars, cables, discs, blades, shafts, membranes, plates and shells that were published in 1992‐1995.

Marine exploration is becoming an important element of pervasive computing underwater target tracking. Many pervasive techniques are found in current literature, but only scant research has been conducted on their effectiveness in target tracking.

This research paper, introduces a Shifted Rayleigh Filter (SHRF) for three-dimensional (3 D) underwater target tracking. A comparison is drawn between the SHRF and previously proven method Unscented Kalman Filter (UKF).

SHRF is especially suitable for long-range scenarios to track a target with less solution convergence compared to UKF. In this analysis, the problem of determining the target location and speed from noise corrupted measurements of bearing, elevation by a single moving target is considered. SHRF is generated and its performance is evaluated for the target motion analysis approach.

The proposed filter performs better than UKF, especially for long-range scenarios. Experimental results from Monte Carlo are provided using MATLAB and the enhancements achieved by the SHRF techniques are evident.

The purpose of this paper is to investigate the effect of the replacement of natural coarse aggregate (NCA) with different percentages of recycled coarse aggregate (RCA) on properties of low calcium fly ash (FA)-based geopolymer concrete (GPC) cured at oven temperature. Further, this paper aims to study the effect of partial replacement of FA by ground granulated blast slag (GGBS) in GPC made with both NCA and RCA cured under ambient temperature curing.

M25 grade of ordinary Portland cement (OPC) concrete was designed according to IS: 10262-2019 with 100% NCA as control concrete. Since no standard guidelines are available in the literature for GPC, the same mix proportion was adopted for the GPC by replacing the OPC with 100% FA and W/C ratio by alkalinity/binder ratio. All FA-based GPC mixes were prepared with 12 M of sodium hydroxide (NaOH) and an alkalinity ratio, i.e. sodium hydroxide to sodium silicate (NaOH:Na₂SiO₃) of 1:1.5, subjected to 90^°C temperature for 48 h of curing. The NCA were replaced with 50% and 100% RCA in both OPC and GPC mixes. Further, FA was partially replaced with 15% GGBS in GPC made with the above percentages of NCA and RCA, and they were given ambient temperature curing with the same molarity of NaOH and alkalinity ratio.

The workability, compressive strength, split tensile strength, flexural strength, water absorption, density, volume of voids and rebound hammer value of all the mixes were studied. Further, the relationship between compressive strength and other mechanical properties of GPC mixes were established and compared with the well-established relationships available for conventional concrete. From the experimental results, it is found that the compressive strength of GPC under ambient curing condition at 28 days with 100% NCA, 50% RCA and 100% RCA were, respectively, 14.8%, 12.85% and 17.76% higher than those of OPC concrete. Further, it is found that 85% FA and 15% GGBS-based GPC with RCA under ambient curing shown superior performance than OPC concrete and FA-based GPC cured under oven curing.

The scope of the present paper is limited to replace the FA by 15% GGBS. Further, only 50% and 100% RCA are used in place of natural aggregate. However, in future study, the replacement of FA by different amounts of GGBS (20%, 25%, 30% and 35%) may be tried to decide the optimum utilisation of GGBS so that the applications of GPC can be widely used in cast in situ applications, i.e. under ambient curing condition. Further, in the present study, the natural aggregate is replaced with only 50% and 100% RCA in GPC. However, further investigations may be carried out by considering different percentages between 50 and 100 with the optimum compositions of FA and GGBS to enhance the use of RCA in GPC applications. The present study is further limited to only the mechanical properties and a few other properties of GPC. For wider use of GPC under ambient curing conditions, the structural performance of GPC needs to be understood. Therefore, the structural performance of GPC subjected to different loadings under ambient curing with RCA to be investigated in future study.

The replacement percentage of natural aggregate by RCA may be further enhanced to 50% in GPC under ambient curing condition without compromising on the mechanical properties of concrete. This may be a good alternative for OPC and natural aggregate to reduce pollution and leads sustainability in the construction.

This paper delves into the mechanism of the contingency framework for foreign entry mode decisions and identifies two essential tasks that jointly determine the outcome of the entry mode decision. It then recognizes a critical weakness in previous research pertaining to the comparison of entry modes along a key decision criterion, the degree of control. Existing studies generally treat equity involvement as the only source of entrant control, while largely ignoring non‐equity sources of control (i.e., bargaining power and trust). Non‐equity sources of control, when underutilized, amount to missed opportunities, increased resource commitments, and heightened risk exposures in foreign markets. Drawing from a pluralism perspective in transaction and relationship governance, the author presents a more integrative method for the ranking of entry modes along the degree of control. The central message is that companies entering foreign markets should make an earnest effort to identify trust and bargaining power situations and fully utilize their control potential in making entry mode decisions.

This paper aims to address the magnetohydrodynamic boundary layer flow of hybrid mixture across a stretching surface under the influence of electric field.

The local similarity transformations are implemented to reformulate the governing partial differential equations into coupled non-linear ordinary differential equations of higher order. The numerical solutions are obtained for the simplified governing equations with the aid of finite difference technique.

The velocity, temperature and entropy generation are examined thoroughly for the effects of different budding parameters related to present analysis by means of graphs. It is obtained that owing to the effect of magnetic field along with slip factor, the fluid motion slowdown. However, the flow velocity enhances for the rising estimations of an electric field which tends to resolve sticky effects.

The three-dimensional plots are drawn to understand the nature of physical quantities. To ensure the precision, the obtained solutions are compared with the existing one for certain specific conditions. A good concurrence is observed between the proposed results and previously recorded outcomes.

This study examines the empirical relationship between four broad antecedents of brand equity (branding strategy, brand structure, brand positioning and target market) and two separate dimensions of revenue premium: price premium and volume premium. Our modeling framework aims to explain how different antecedents of brand equity influence the realized velocity and margin of branded product sales, key drivers of operating cash flow. Our generalizable empirical analyses are based on a representative dataset of over 6,500 brands, across 200 consumer-packaged goods categories, spanning three years. We find that only 20% of brands command revenue premiums, for which volume premiums are the critical determinant. Branding strategies and brand structure primarily impact volume premium. In contrast, brand positioning has little effect. Target market substantially affects both premiums. Overall, these four elements account for 73% and 69% of the explained variations in price and volume premiums, respectively. This study provides generalizable, important, and novel insights for the theory and practice of brand management regarding price positioning and extending brands into new categories.

This study aims to investigate the optimal process parameters of the wire-cut electrical discharge machining (WCEDM) for the machining of the GZR-AA7475 hybrid metal matrix composite (HMMC). HMMCs are prepared with 2 Wt.% graphite and 4 Wt.% zirconium dioxide reinforced with aluminium alloy 7475 (GZR-AA7475) composite by using the stir casting method. The objective is to enhance the mechanical properties of the material while preserving its unique features. WCEDM with a 0.18 mm molybdenum wire electrode is used for machining the composite.

To conduct experimental studies, a Taguchi L27 orthogonal array was adopted. Input variables such as peak current (I_p), pulse-on-time (T_ON) and flushing pressure (P_F) were used. The effect of process parameters on the output responses, such as material removal rate (MRR), surface roughness rate (SRR) and wire wear ratio (WWR), were investigated. The grey relational analysis (GRA) is used to obtain the optimal combination of the process parameters. Analysis of variance (ANOVA) was also used to identify the significant process parameters affecting the output responses.

Results from the current study concluded that the optimal condition for grey relational grade is obtained at T_ON = 105 µs, I_p = 100 A and P_F = 90 kg/cm². Peak current is the most prominent parameter influencing the MRR, whereas SRR and WRR are highly influenced by flushing pressure.

Identifying the optimal process parameters in WCEDM for machining of GZR-AA7475 HMMC. ANOVA and GRA are used to obtain the optimal combination of the process parameters.

The purpose of this study is to explore how and when an employee's belief in their voice self-efficacy leads to promotive and prohibitive voice behavior. By banking on social cognitive theory, this study examines perceived influence at work as a mediator and managerial openness as a moderator in the link between voice self-efficacy and the two forms of voice.

This study's data come from 285 Indian information technology (IT) employees by adopting a cross-sectional survey design. The effect of moderator and mediator is examined by employing structural equation modeling in AMOS 22.

The results reveal that perceived influence at work partially mediates the positive link between voice self-efficacy and the two forms of voice behaviors. The test of moderation also exposes that prohibitive voice is more contingent on managerial openness as compared to promotive voice.

This is one of the initial studies to explore perceived influence at work as a mediator in the association between voice self-efficacy and employee voice behavior. The treatment of voice as a bidimensional construct in this study discloses the difference between the two forms, contributing to the voice literature and inviting further research.

This study examines the entry mode and ownership strategies in China, South‐East Asia and Western Europe made by manufacturing firms in Taiwan. The results find that when the larger, high R&D and high advertising intensive Taiwanese manufacturing firms invest in China, South‐East Asia and Western Europe, they would be likely to choose the greenfield‐WFOE entry. On the other hand, when these firms have the most foreign investing experiences and the longest investing history in China, South‐East Asia and Western Europe, the acquisition‐WFOE entry would tend to be preferred. Finally, this study proposes relevant implications for practice in the conclusion.